Linux version 2.4.18-3 (bhcompile@daffy.perf.redhat.com) (gcc version 2.96 20000731 (Red Hat Linux 7.3 2.96-110)) #1 Thu Apr 18 07:37:53 EDT 2002 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f400 (usable) BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000007ffc000 (usable) BIOS-e820: 0000000007ffc000 - 0000000007fff000 (ACPI data) BIOS-e820: 0000000007fff000 - 0000000008000000 (ACPI NVS) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) On node 0 totalpages: 32764 zone(0): 4096 pages. zone(1): 28668 pages. zone(2): 0 pages. Kernel command line: ro root=/dev/hdb5 hdc=ide-scsi hdd=ide-scsi ide_setup: hdc=ide-scsi ide_setup: hdd=ide-scsi Initializing CPU#0 Detected 736.016 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 1468.00 BogoMIPS Memory: 126120k/131056k available (1119k kernel code, 4548k reserved, 775k data, 280k init, 0k highmem) Dentry cache hash table entries: 16384 (order: 5, 131072 bytes) Inode cache hash table entries: 8192 (order: 4, 65536 bytes) Mount-cache hash table entries: 2048 (order: 2, 16384 bytes) Buffer cache hash table entries: 4096 (order: 2, 16384 bytes) Page-cache hash table entries: 32768 (order: 5, 131072 bytes) CPU: Before vendor init, caps: 0383f9ff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU: After vendor init, caps: 0383f9ff 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000 CPU: Common caps: 0383f9ff 00000000 00000000 00000000 CPU: Intel Pentium III (Coppermine) stepping 03 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel PCI: PCI BIOS revision 2.10 entry at 0xf0890, last bus=1 PCI: Using configuration type 1 PCI: Probing PCI hardware Unknown bridge resource 0: assuming transparent PCI: Using IRQ router VIA [1106/0596] at 00:04.0 Activating ISA DMA hang workarounds. isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16) Starting kswapd VFS: Diskquotas version dquot_6.5.0 initialized pty: 2048 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A Real Time Clock Driver v1.10e block: 240 slots per queue, batch=60 Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller on PCI bus 00 dev 21 VP_IDE: chipset revision 16 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt82c596b (rev 23) IDE UDMA66 controller on pci00:04.1 ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:pio hda: IBM-DTLA-307030, ATA DISK drive hdb: ST315323A, ATA DISK drive hdc: MATSHITA CD-RW CW-7585, ATAPI CD/DVD-ROM drive hdd: MATSHITA CD-RW CW-7585, ATAPI CD/DVD-ROM drive hdd: set_drive_speed_status: status=0x01 { Error } hdd: set_drive_speed_status: error=0x04 ide1: Drive 1 didn't accept speed setting. Oh, well. ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=3737/255/63, UDMA(66) hdb: 30008475 sectors (15364 MB) w/512KiB Cache, CHS=1867/255/63, UDMA(66) ide-floppy driver 0.99.newide Partition check: hda: hda1 hda2 < hda5 > hdb: hdb1 hdb3 < hdb5 hdb6 > hdb1: Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize ide-floppy driver 0.99.newide md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 8192 bind 8192) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. RAMDISK: Compressed image found at block 0 Freeing initrd memory: 217k freed VFS: Mounted root (ext2 filesystem). SCSI subsystem driver Revision: 1.00 kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2 PCI: Found IRQ 5 for device 00:0a.0 ncr53c8xx: at PCI bus 0, device 10, function 0 ncr53c8xx: 53c815 detected ncr53c815-0: rev 0x4 on pci bus 0 device 10 function 0 irq 5 ncr53c815-0: ID 7, Fast-10, Parity Checking scsi0 : ncr53c8xx-3.4.3b-20010512 Journalled Block Device driver loaded kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Freeing unused kernel memory: 280k freed Adding Swap: 136512k swap-space (priority -1) Adding Swap: 262136k swap-space (priority -2) usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-uhci.c: $Revision: 1.275 $ time 07:43:07 Apr 18 2002 usb-uhci.c: High bandwidth mode enabled PCI: Found IRQ 9 for device 00:04.2 PCI: Sharing IRQ 9 with 00:09.0 PCI: Sharing IRQ 9 with 00:0d.0 PCI: Sharing IRQ 9 with 00:0d.1 usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 9 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.275:USB Universal Host Controller Interface driver hub.c: USB new device connect on bus1/1, assigned device number 2 usb.c: USB device 2 (vend/prod 0x41e/0x4004) is not claimed by any active driver. EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,69), internal journal hdd: set_drive_speed_status: status=0x01 { Error } hdd: set_drive_speed_status: error=0x04 ide1: Drive 1 didn't accept speed setting. Oh, well. scsi1 : SCSI host adapter emulation for IDE ATAPI devices Vendor: MATSHITA Model: CD-RW CW-7585 Rev: 1.04 Type: CD-ROM ANSI SCSI revision: 02 hdd: status error: status=0x01 { Error } hdd: status error: error=0x04 ide-scsi: Strange, packet command initiated yet DRQ isn't asserted hdd: status error: status=0x01 { Error } hdd: status error: error=0x04 ide-scsi: Strange, packet command initiated yet DRQ isn't asserted hdd: status error: status=0x01 { Error } hdd: status error: error=0x04 ide-scsi: Strange, packet command initiated yet DRQ isn't asserted hdd: status error: status=0x01 { Error } hdd: status error: error=0x04 hdd: DMA disabled （途中同様なエラーが続くので省略） ide-scsi: Strange, packet command initiated yet DRQ isn't asserted hdd: ATAPI reset complete hdd: status error: status=0x01 { Error } hdd: status error: error=0x04 ide-scsi: Strange, packet command initiated yet DRQ isn't asserted hdc: DMA disabled hdd: DMA disabled parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP] parport0: irq 7 detected ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker http://www.scyld.com/network/ne2k-pci.html PCI: Found IRQ 9 for device 00:09.0 PCI: Sharing IRQ 9 with 00:04.2 PCI: Sharing IRQ 9 with 00:0d.0 PCI: Sharing IRQ 9 with 00:0d.1 eth0: RealTek RTL-8029 found at 0xd000, IRQ 9, 00:90:CC:A4:3A:49. PCI: Found IRQ 10 for device 00:0b.0 Linux video capture interface: v1.00 i2c-core.o: i2c core module i2c-algo-bit.o: i2c bit algorithm module i2c-core.o: driver i2c msp3400 driver registered. i2c-core.o: driver i2c TV tuner driver registered. bttv: driver version 0.7.91 loaded bttv: using 2 buffers with 2080k (4160k total) for capture bttv: Host bridge is VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] bttv: Host bridge is VIA Technologies, Inc. VT82C596 Power Management bttv: Bt8xx card found (0). PCI: Found IRQ 9 for device 00:0d.0 PCI: Sharing IRQ 9 with 00:04.2 PCI: Sharing IRQ 9 with 00:09.0 PCI: Sharing IRQ 9 with 00:0d.1 bttv0: Bt878 (rev 17) at 00:0d.0, irq: 9, latency: 32, memory: 0xe1000000 bttv0: subsystem: 10fc:4080 (UNKNOWN) please mail id, board name and the correct card= insmod option to kraxel@bytesex.org bttv0: using: BT878(GV-BCTV3) [card=49,insmod option] i2c-algo-bit.o: Adapter: bt848 #0 scl: 1 sda: 1 -- testing... i2c-algo-bit.o:1 scl: 1 sda: 0 i2c-algo-bit.o:2 scl: 1 sda: 1 i2c-algo-bit.o:3 scl: 0 sda: 1 i2c-algo-bit.o:4 scl: 1 sda: 1 i2c-algo-bit.o: bt848 #0 passed test. tuner: probing bt848 #0 i2c adapter [id=0x10005] tuner: chip found @ 0xc0 bttv0: i2c attach [client=Alps TSCH6,ok] i2c-core.o: client [Alps TSCH6] registered to adapter [bt848 #0](pos. 0). i2c-core.o: adapter bt848 #0 registered as adapter 0. bttv0: i2c: checking for TDA9875 @ 0xb0... not found bttv0: i2c: checking for TDA7432 @ 0x8a... not found bttv0: registered device video0 bttv0: registered device vbi0 bttv0: PLL: 28636363 => 35468950 ... ok Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0 sr0: scsi3-mmc drive: 8x/32x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12